Isla Bennett
The Senco FinishPro-35 Finish Nailer is a handy tool, but it can be frustrating when you need to remove nails from it. Some users have struggled with getting the unspent nails out of the nailer, while others have encountered issues with jammed nails or difficulty unloading nails from the magazine. There are a few methods to remove nails from the Senco FinishPro 35, including releasing the feeder shoe, using the thumb-sized hole to release tension, and opening the front latch to push out all the nails. With these methods, you can efficiently remove nails and get back to your projects.
| Characteristics | Values |
|---|---|
| Nail removal method | Release the feeder shoe and slide it forward, then remove fasteners from the tool |
| Feeder shoe release mechanism | Pull the shoe towards the rear of the gun, insert finger into the hole and gently press, causing a flat metal tab to bend slightly, allowing the shoe to slide forward |
| Nail strip removal | Slide the nail strip out the rear of the gun |
| Piston and driver assembly removal | Video tutorial available on eReplacementParts.com |
| Air leak issue | Seals are not sold as a kit, but individually |
| Seal/Rebuild Kit part number | yk0365 |
| Nail angle issue | Ensure nails are loaded head first with points outward |
| Nail type | Senco headless nails, 16-gauge |
| Nail loading | Nails should be loaded with the gun upside down |
| Nail feeding mechanism | Spring-loaded piece with a metal ribbon fastened to the front of the nail magazine |
Explore related products
What You'll Learn
Release the feeder shoe
To release the feeder shoe of the Senco FinishPro-35 Finish Nailer, follow these steps:
Firstly, pull the feeder shoe slightly towards the rear of the gun. This action will remove the tension on the nail strip. The feeder shoe is the component with a thin metal coil attached to it, and it is responsible for pushing the nails upward.
Next, locate the hole on the feeder shoe, which is approximately the size of your thumb. Insert your finger into this hole and gently apply pressure. This action will cause a flat metal tab, which typically pushes the nail strip forward, to bend slightly away from the nail strip.
With the metal tab bent, the feeder shoe is now ready to be slid forward. Simply slide the feeder shoe forward, and then you can easily remove the nail strip out of the rear of the gun.
If your FinishPro-35 is similar to the 41XP model, an alternative method is to push down on the bottom of the feeder shoe. This action will flip the feeder mechanism upward and over the nails. Then, simply slide the nails down and out of the bottom.
How Nail Polish Removal Happens After Death
You may want to see also
Explore related products
Slide the feeder shoe forward
To remove nails from the Senco FinishPro-35 Nailer, you must first release the feeder shoe. The instruction manual provides the following guidance: "Release the feeder shoe and slide it forward. Remove fasteners from the tool." However, it does not explain how to release the feeder shoe.
The feeder shoe has a hole roughly the size of your thumb. To release the feeder shoe, follow these steps:
- Pull the shoe slightly towards the rear of the gun to remove the tension on the nail strip.
- Insert your finger into the hole and press gently. This will cause a flat metal tab (which normally pushes the nail strip forward) to bend slightly, becoming proud of the nail strip.
- Now the feeder shoe should be able to slide forward.
- Finally, slide the nail strip out the rear of the gun.
If your FinishPro-35 Nailer is the same as the 41XP model, there is an alternative method to release the feeder shoe:
- Push down on the bottom of the feeder shoe.
- This should flip the feeder mechanism upward over the nails.
- With the mechanism out of the way, slide your nails down and out the bottom.
Gel Nail Polish: Kid-Friendly or Not?
You may want to see also
Explore related products
Remove the fasteners
To remove the fasteners from your Senco FinishPro-35 Finish Nailer, follow these steps:
Firstly, locate the feeder shoe. This is the part with a thin metal coil attached to it, which pushes the nails upward. Pull the feeder shoe slightly towards the rear of the gun to release tension on the nail strip. The feeder shoe has a hole about the size of your thumb. Insert your finger into this hole and press gently. This action will cause a flat metal tab, which usually pushes the nail strip forward, to bend slightly away from the nail strip.
With the tension released and the metal tab bent, the feeder shoe should now be free to slide forward. Slide the feeder shoe forward, and then simply slide the nail strip out the rear of the gun. Your fasteners are now removed.
If your nail gun becomes jammed, or you are unable to remove the fasteners using the above method, you may need to disassemble the gun to remove the nails. This can be done by removing the air supply and opening the front latch, which will release all the nails. Alternatively, you can remove the head of the gun and push the piston down into the cylinder until it hits the lower bumper.
Easy Steps to Remove ColorStreet Nails
You may want to see also
Explore related products
Remove the piston and driver assembly
To remove the piston and driver assembly from a Senco FinishPro 35 nail gun, you can follow the steps outlined in a video provided by eReplacementParts.com. Removing the piston and driver assembly will allow you to replace a broken driver or access other parts that may be affecting the performance of your nail gun.
Firstly, you will need to remove the seals from the nail gun. Unfortunately, these seals are not sold as a kit, but individually. Once you have obtained the necessary seals, you can proceed with the removal of the piston and driver assembly. It is recommended to refer to the video for a comprehensive understanding of the process, as visual guidance can be invaluable when undertaking such tasks.
By following the steps outlined in the video, you will be able to successfully remove the piston and driver assembly from your Senco FinishPro 35 nail gun. This will grant you access to internal components, allowing for repairs, replacements, or adjustments to enhance the performance of your tool.
Easy Ways to Remove Hair Dye from Skin and Nails
You may want to see also
Explore related products
Disassemble the gun
To disassemble the Senco FinishPro 35 nail gun, you will need to remove the air supply and open the front latch. This will cause all the nails to be pushed out. If this does not work, you can try removing the head and pushing the piston down into the cylinder until it hits the lower bumper.
If you are still unable to unload the nails, you may need to take the gun apart. First, remove the head, then the base. If this does not solve the problem, you will need to remove the trigger assembly. Please note that this is a complex process, and you may want to seek expert advice before proceeding.
You can also try removing the piston and driver assembly to replace a broken driver or access other parts that may be affecting the gun's performance. This process is demonstrated in a video available on eReplacementParts.com.
Another user has suggested that the nail strip can be removed by pulling the feeder shoe towards the rear of the gun to release the tension on the nail strip. Then, insert your finger into the hole in the feeder shoe and press gently. This will cause a flat metal tab to bend slightly, allowing the feeder shoe to slide forward. Finally, slide the nail strip out the rear of the gun.
Acrylic Powder and Gel Nails: A Match Made in Heaven?
You may want to see also
Frequently asked questions
According to the instruction manual, removing the nails is as simple as "Release the feeder shoe and slide it forward. Remove fasteners from the tool." To release the feeder shoe, pull it slightly towards the rear of the gun to remove the tension on the nail strip. Then, insert your finger into the hole (about the size of your thumb) and press gently. This will cause a flat metal tab to bend slightly, allowing the feeder shoe to slide forward. Finally, slide the nail strip out the rear.
If the above method doesn't work, you may need to disassemble the gun to remove unused nails.
Yes, another method is to remove the air supply and pop open the front latch, which will push out all the nails.
If the nail strip is protruding from the magazine, you may be able to grasp and pull it out. Otherwise, you may need to contact an appliance technician for help.
